Wet room installation kit

This means the space around the drain and the pipe needs back filling with either a weak sand and cement mortar or powder tile adhesive.

This has to done in such a way that, when the adhesive or mortar sets, the drain and pipe is in exactly the right position. To do this the back filling and bonding down of the deck needs to be done at the same time so the drain can be fitted to the deck and the back filling flows around the final position of the drain and pipe.

Any deck can be inset in to a solid floor with a similar proceed as for overlaying a solid floor but also chipping away enough of the concrete or screed so the complete deck can be dropped in to ground level. The deck is bedded in to the recess using powder tile adhesive or a sand and cement mortar. Guide 3 — Wetroom Kit Installation Wetroom Innovations supplies detailed installation instructions with each kit these can be downloaded here , however at the planning stage you might want to know a bit more about how each type of kit is installed so you can make a more informed choice.

This guide explains the basic installation of: Maxxus structural shower deck wet room kit — the easiest and quickest kit to install. You might also want to have a look at the supplementary guides covering: Guide 4. The rest of job will be to plumb in the shower and then to select and fit a shower screen. Steps to installing a Maxxus Wetroom Tray on a suspended timber floor 1. Cut out in the floor may not match joists or boarding joints Note: The tray can be cut down as long as you have enough of the wet area covered.

Match the floor level using Tile backer board or Plywood. Flooring edges reinforced to stop movement between floor and deck. Installation of an Underlay foam cored, non-structural Wet Room Deck Kit Two techniques are available: Over boarding — Which allows the rest of the floor to be insulated with tile backer board, ideal for under tile heating.

Underlay over existing floor leveled off with TBB or Plywood 2. Make a solid base for the drain and mark where the drain needs to be positioned. Inset — Steps to installing a Underlay Foam Cored Wetroom Tray in to a suspended timber floor If the level of the floor can only be raised by a few millimetres and you have chosen an underlay deck rather than a Maxxus the follow technique is the solution. The underlay needs full, solid support at joist level 3.

Level off the floor with Ply, TBB or Plastic Ply See the full range of Underlay square drain kits — Underlay kits with linear channel drains are also available Steps to installing a Wetroom kit on a solid floor A wet room tray can be installed on top of an existing floor and the rest of the floor built up to the same height or inlaid. Inset a wetroom kit in to a solid floor Any deck can be inset in to a solid floor with a similar proceed as for overlaying a solid floor but also chipping away enough of the concrete or screed so the complete deck can be dropped in to ground level.

Guide 1 — Wetroom Design Planner Inspiration and Ideas for creative wetroom planning including the downloadable planner sheets. Guide 2 — Wetroom Floors and Drainage What you need to know to plan your floor and drainage.

Guide 3 — Wetroom Kit Installation Overview of how to install a wetroom kit on various types of floors. Guide 4 — Tips on Drains and Waste Installation for Wetrooms A few tips to help you plan how the waste pipe can be routed and connected. Sign in to your account Account Login Username. Sign in. Forgot your password? This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Close Privacy Overview This website uses cookies to improve your experience while you navigate through the website.

Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website.

These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.

Styling options include: Having no separation at all between the shower and the wider floor. Using a half or full glass door for the shower, but extending the same flooring throughout the entire room. Taking out the bathtub completely and replacing it with a shower faucet. Modifying your hand-held shower over the tub while ensuring the room feels unbroken and open. Removing your shower tray and retiling the whole floor using uniform slabs.

There might be a tub, but more often, you just have a shower. The entire room is waterproof, from floor to ceiling. Why do you want a wet room? Yes, they can be expensive, but also: Comprehensive wet room kits are easy to buy, making your bathroom restoration process much easier.

You can even follow instruction videos on YouTube. With no raised shower tray, wet rooms offer easier access to the elderly. For those who love to scrub the shower before they step in, the wide-open wet room spreads steam farther along the walls and floors, making the whole space easier to clean.

By converting a smaller bathroom into a wet room, you can give your entire space a new feel. This can be helpful for old inherited houses or flipped foreclosures. Wet rooms use up more water and power than shower cubicles, so your utility bills are higher.

Some users feel disoriented in that wide-open bathroom space. Factors to consider when installing a wet room Making the decision to go wet is easy. This may involve inspecting and clearing your drains and gutters. The largest characteristic of wet rooms is wide open space, so opt for space-saving fixtures like hidden piping and recessed shower heads built into the ceiling.

Wet room design is generally minimalist, so you may veer towards chromes and metallics that do well with steamy sauna-like bathroom spaces. It may also be important to remove all bath linens — towels, washcloths, even toilet paper, because they easily get damp and might cause mold and mildew.

While you do want a floor gradient, it needs to be subtle. Otherwise, it may disorient you, especially for kids and older residents. The type of tile or stone you use should be designated for bathroom use. This means it will have a longer-lasting seal and low-slip properties.

Yes, your wet room is free and open, but consider installing handgrips and grab bars. It a steamy, glossy bath area, it can be comforting to have something to hold on to. How to ensure your wet room is waterproof Standard bathrooms use tile and stone, because these are attractive, resistant to moisture, and easy to clean. I have honestly found, Wet Room Materials to be an easy and reliable company to work with. They take care of the specification and advising us on correct build ups and preparation.

On a recent project we were able to buy their Unislope System p from our bathroom show room retailer and they subsequently came to site to tank out the bathrooms. It was a time sensitive job and The Wet Room lads worked through the evening and into the weekend to ensure we completed the project on time.

I have no hesitation in recommending Wet Room Materials. They were willing to stand over their tanking system and more than helpful throughout all stages of the installation from site survey and room preparation to installation.

A 10 Year no leak fully insured warranty gave me the confidence that we were dealing with a professional organisation. I would highly recommend these guys and will certainly be using them going forward. I have honestly found, Wet Room Materials to be an easy and reliable company to work with. They take care of the specification and advising us on correct build ups and preparation. On a recent project we were able to buy their Unislope System p from our bathroom show room retailer and they subsequently came to site to tank out the bathrooms.

It was a time sensitive job and The Wet Room lads worked through the evening and into the weekend to ensure we completed the project on time. I have no hesitation in recommending Wet Room Materials.

They are a pleasure to deal with. In Bright Designs, we understand the importance of specifying a reliable waterproofing system for bathrooms. We have worked on a number of projects with Wet Room Materials over the years and I can honestly say that their waterproofing installation service offers complete peace of mind for us and our clients. The Wet Room Materials Team are there throughout all stages of the project from site survey and specification to installation.

More importantly they also give us a 10 year no leak guarantee. I also like the fact that they will handle communication with the client and contractors in terms of delivering a high-quality installation which allows me the head space to focus on other aspects of the build. Wetroom Installation Products Wet room installation materials designed for professionals when fitting a wet room; waterproofing, tile adhesive, screed and more.